NEW Boat Neck Design | Latest Kurti Neck Designs | BST

NEW Boat Neck Design | Latest Kurti Neck Designs | BST


If you have not SUBSCRIBED our channel till now, then press the red button below to subscribe Don’t forget to press the bell icon to receive notifications for our latest videos. You’re watching “Best Stitching Tutorials”. And today we’re going to show – How to make Boat Neck Design using flowers. For this we have taken, fusion paper (paper buckram) It’s length is 13 inch and width is 8 inch. Now, we will make it in two folds. And we will start the marking for neck design. From the closed side, we will take the neck as 4.5 inches. From the top we will mark 4 inches. Now, we will join these two marks by giving boat neck shape. We will draw another curve (outer curve) at a distance of 2 inch from inner curve. First we will cut the inner curve. And after that we will cut the outer curve. Now, we will paste it on the fabric. We have placed the fusion paper on the fabric and now we will iron it. We will leave some cloth beside fusion paper and cut the remaining fabric. Now, we will show the stitching. First, we will prepare the boat neck shape on fusion paper. We will fold the outer cloth on the fusion paper and stitch it. This is the front part of Kurti. and we’ve placed the wrong side on top. We have also marked the centre line on the wrong side. Now, we will place the neck on it. Now, we will place the front part of Kurti and Neck together such that their cut mark at centre coincide with each other. And we will stitch here at the centre. After that we will stitch alongside this fusion paper. Now, we will leave some fabric alongside fusion paper and cut the remaining fabric. We will make cut marks along this curve using scissor. And we will remove this stitching at centre. We will fold the fusion paper (buckram) to the other side. And we will stitch alongside this curve. Similarly we will stitch along the outer curve on the fusion paper (buckram). We have placed the ribbon by leaving a gap along the curve. And we will stitch it. We will make one more stitch on this side. In the same way, we will keep all ribbon by giving some gap on the fusion paper (buckram). We have stitched all the four ribbons by giving same gap in between them. For the neck design, we will use these flower design. We have made this design using satin ribbon. The width of this ribbon is 2.5 cm. For making one flower design, you will require 1.5 metre length of ribbon (approx.) Now, we will start making the flower design. First, we will slightly burn the end of the ribbon. Now, we will fold the ribbon in the wrong side. This one is wrong side. First, we will fold the ribbon from one corner as shown. Similarly, we will fold it from the other side. You will get pointed corner on top after folding from both sides. These two must corners must be placed together. Now, we will fold it again. After folding this, From this side…where wrong side is present we will fold it again and make a pointed corner. Now, we will place all the petals over one another. In the same way, we will fold the ribbon again. Similarly, we will fold it again. Now, again will fold this petal over the previous ones. We have made 3 petals. We will hold these 3 petals together, and will stitch them together using needle and thread. We will stitch these petals at center of our flower design. After stitching these petals, we will make more petals in the same way. We have made more petals. Now, we will pin them together. Over this petal, we will make remaining petals for our flower design. When you make two or three petals, then be sure to stitch them together. In the same way, we will make more petals and complete the circumference. We will make 18 petals in one flower design. Now, we will make the last petal. For now, we will not stitch the last petal with needle. First we will cut the ribbon at the end. And we will slightly burn the end of the ribbon. Finally, we will make last petal. The size of the flower will depend on the width of the ribbon you have taken. We will remove the pin. We will stitch the first and last petal together using needle. We will attach one pearl at the top of this flower. We will insert the needle from the bottom. And insert this pearl into the needle. On this pearl we will place this bead We’re using this bead to hold the thread when we insert the needle back into the pearl. We have attached these flower designs in our neck design. SUBSCRIBE our channel to watch more such designs. And don’t forget to LIKE this video.

52 thoughts on “NEW Boat Neck Design | Latest Kurti Neck Designs | BST

  1. Mam its super and awesome, So beautiful i liked it ,i will definetly gonna tyr itAlso english subtitles hrlped me a lot ,hope titles for further vedios also
    THANK YOU MAAM

Leave a Reply

Your email address will not be published. Required fields are marked *